Guide To Flash Doogee X7S MT6737M Marshmallow 6.0 Flashtool Tested Method

GUIDE TO FLASH DOOGEE X7S MT6737M

 MARSHMALLOW 6.0 FREE FIRMWARE DOWNLOAD

INFO:

Wait for phone...
Phone found! [ 7 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6737
BB_CPU_NME : [MediaTek] MT6737M|MT6737_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 460001154D323238D8E800426DD5559B
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM228
[eMMC] : FLASH_CID : 150100463832324D4200E8D89B55B36D
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID : 0x4ABAA9BD2C7FB165E07AFBAC0333942D
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[AP] : Initial info read Ok!
Brand : DOOGEE
ProdName : x6069_dg_a50s_ah
ProdModel : X7 S
Device : x6069_dg_a50s_ah
AndroidVer: 6.0
MTKxCPU : MT6737M
MTKxPRJ : alps-mp-m0.mp1-V2.84_wtk6737m.65.m0
Done!

MT6737M__DOOGEE__X7_S__x6069_dg_a50s_ah__6.0__alps-mp-m0.mp1-V2.84_wtk6737m.65.m0

PRE-REQUISITE

• This is for Doogee X7s only.
• Your device must have 70% Of battery.
• You need a Laptop or PC to perform this Action.
• Download the right firmware for X7s from the link bellow.
• Back Up your Data to make sure you have data’s in case if something Wrong (This Process won’t loose your data)
• Make sure you have followed the steps properly. Don’t Skip and Read!
• We are not responsible for any damage that you make to your Phone.

WHY YOU NEED TO FLASH YOUR PHONE!!

You need this firmware/stock rom if you have encountered this kind of problem in your Smartphone Listed Below:

1.Hang on logo.
2.Rebooting.
3.Bootloop & Dead boot after a wrong software.
4-Virus & Sexual Apps.
5-System crashing

How to know if the phone had a hard problem (Emmc problem)??

• What is Emmc problem? also called read mode only,  it means that your internal memory doesnt accept command, so the phone stay on the same condition after a software or a hard reset.
•  if the phone hang on logo after flash, you ara facing Emmc problem.
• As a precaution you shouldn't change setting in SP flashtool from Download only to format+download, you will end with a dead phone if you have a Emmc problem ofcourse.

DOWNLOAD AREA:

Firmware Download Link: HERE Or FROM HERE

Password For Firmware: Here
SP Flashtool Downloadlink: SPFlashTool 5.1628
Drivers Download Link: Mobile Mtk Drivers

How To Flash Via SP FLASHTOOL?

1-Requirements:

1. • A Computer PC Run Windows XP or above
   • Usb data cable (not a generic cable)
   • Mtk usb drivers installed manually, you will find instruction bellow
   • Your Mtk Smartphone Face a soft issue
   • Original stock rom (you can find it above in download section)
   • The latest SP Flashtool version
   
   
   2-How to install VCOM Drivers:
   • Open device manager from my PC or my computer.
   • Click on any item and go to actions > Add legacy hardware
   • Now, press next and select install drivers manually
   • Press next and click on have disk
   • from the browse option, select VCOM drivers From mtk drivers folder
   • Once its done. You will see a screen similar to this:
   
   
   
   
   
   
   
   
   
   • Once you are done with the driver installation, go to device manager > Ports (COM&LPT) you will find a device similar to this:
   
   
   
   
   
   
   
   3-How to flash rom using SP Flashtool?:
   
   
   • Power the phone off, remove the battery from the smartphone and put it back without booting the phone (if the battery is inside then simply switch it off).
   • Launch SP Flashtool 
   
   
   
   *Double clicks onFlash_tool.exe
   
                                          *Press OK
   
   
   
   
   
   
   
   
   
   
   
   
   
   • Click on scatter-loading option and browse to the scatter file of your stock rom choose MTxxxx_android.txt (scatter.txt).
   
   
   
   
   
   
   
   
   
   
   • Dont touch any options, Keep the original setting (In case you want to format device before flash press choose format+download but it'snt recommanded because you will be ended with an EMEI null)
   • If you phone is alive and has a software issue (contain virus, Stuck on logo, apps setting problem, blink, or not work as expected) I advise you to Uncheck Preloader as a precaution. On contarary check all pertitions if you have a boot problem (you phone does'nt boot when you try to power on it).
                                  
   
   
   
   • Once you are done with everything, click on the download button at the top of the software.
   
   
   
   
   
   
   
   Stop should now be prominent while other options should be grayed out
   
   
   
   
   • Connect your switched off phone with battery inside to PC via Usb cable
   • A progressbar should start running
   
   
   
   
   
   • In the end of an success flash process, a box should show up with green OK symbol inside
   
   
   
   
   
   • Disconnect the phone, remove the battery, slot it back in then power the phone.

ENJOY.